Msd 7761 Advance RPM Control Module Installation User Manual download pdf

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

Parts Included:

1 - Module

1 - Parts Bag

MSD Advanced RPM Control Module

PN 7761

ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered in our

monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product will help if there

is ever a warranty issue with your product and helps the MSD R&D team create new products that you

ask for! Go to www.msdignition.com/registration.

1 - 8’ DS Sensor extension harness

Required Items for Operation:

MSD Power Grid - PN 7730

MSD CAN-Hub - PN 7740

Hall Effect Sensor - Racepak PN 800-SS-MSC-5

Driveshaft Collar - Call Racepak

The Advanced RPM Control Module (ARC), PN 7761, has been designed to help prevent excessive

wheel speed. In the event that engine and / or driveshaft rpm increase(s) at an undesirable rate the

module’s software will retard timing and/or rev limiting in order to prevent excessive wheel speed.

INSTALLATION:

The ARC Module should be securely mounted near the MSD CAN-Hub. Plug the ARC CAN connector

to an available port on the MSD CAN-Bus Hub, PN 7740. Do NOT cut the CAN-Bus connector wires.

The driveshaft sensor must plug directly to the 7761 module. MSD recommends using an 8-magnet

driveshaft collar. Using less than an 8-magnet collar will result in less data for the processor to

work with and slower, less reliable corrections.

When connecting to a Racepak Data Recorder, the White/Blue and Brown wires will be connected

to the driveshaft input on the Racepak. The wires (White/Blue and Brown) do not have a connector

on them from the factory; two connectors are included in the parts bag of the module. Select and

install either the 2-pin or 3-pin connector depending on which style is required by the data recorder

being used. To install, push the pins (pre-installed on the wires) into the proper hole according to

Figure 1 below. If these wires are not used, terminate the wires using heat shrink so that they cannot

create a short.

The Yellow output wire is included in the same loom as the driveshaft output wires. The Yellow wire

will switch to ground any time the ARC is controlling timing or rev limiting. The output circuit can

support up to two amps continuous. This can be used to activate a light, solenoid, or boost controller.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - INSTALLATION:

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4Parts Included: 1

Page 2 - MSD 7730 Wiring

2 INSTALLATION INSTRUCTIONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 3 - DRIVESHAFT

INSTALLATION INSTRUCTIONS 3M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 4 - SLEW RATE

4 INSTALLATION INSTRUCTIONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 5 - TIME BASED

INSTALLATION INSTRUCTIONS 5M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 6 - COPY AND PASTE

6 INSTALLATION INSTRUCTIONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 7 - Figure 2 Wiring

INSTALLATION INSTRUCTIONS 7M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Page 8 - TECH NOTES

8 INSTALLATION INSTRUCTIONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7

Comments to this Manuals

No comments

Msd 7761 Advance RPM Control Module Installation User Manual

Browse online or download User Manual for For the car Msd 7761 Advance RPM Control Module Installation. MSD 7761 Advance RPM Control Module Installation User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Msd 7761 Advance RPM Control Module Installation